How to remove the (Important Display Message) after changing the screen of

iPhone 11

INSTRUCTION: For iPhone11 you have to remove the R8156 resistor, R8156 PAD 1# is connected to the touch chip F11, the C8155 capacitor is connected to the touch chip F13, and the L8100 (PP1V8) supplies power to the touch chip connected to E16 on chip .

The post Removing (Important Display Message) on iPhone 11 & 11 Pro MAX – Schematic Diagram appeared first on xFix.

We get a lot of inquiries from people with iPhones displaying Error Code 14. If you are one of these people then you’re probably wanting to find a way of recovering the files and data from your phone, without performing a Factory Reset and wiping its contents.

iPhone Error 14 – How does this happen?
Before the fatal error 14 code is issued, the iPhone will notify you that it is getting very short on memory. The “Storage Almost Full” message that you see is really prompting you to free up some space on the iPhone by deleting some of the data on it. This could be Apps that are no longer used or maybe a few photos or videos: anything that frees up some space on the phone.

If you follow this instruction the “Storage Almost Full” message will disappear and you’ll be able to carry on as normal. The problems come when you don’t do anything about freeing up some space on the iPhone. That space, which was already critically small just gets even smaller until eventually, the phone will fall over as it’s run out of space to function.

Once this happens the iPhone will most probably enter a continuous boot loop. If you connect the iPhone to iTunes and try to restore the phone you’ll see the Error 14 code.

What can be done to recover the data from an iPhone with Error Code 14?
If you Google the error code you’ll see a lot of incorrect advice from Apple and others about changing the USB cable or updating software etc. We’ve never known this to be successful, but you can follow Apple’s advice and give that a go if you want. But in our experience, once the phone is displaying error 14 it’s not possible to recover the data from it. There is simply no space on the phone to allow it to function normally, and there is no workaround. The only choice you have is to factory reset the phone, which will lose the data on it. Hopefully, you’ll have enabled iCloud to store a backup of your data, but if you haven’t your data is lost.

And Finally…

You’ll come across web sites that say they are able to fix this problem, but you’ll find they all want money upfront. That’s the scam – they are just using your desperation to get money out of you. Don’t fall for it, they can’t help you.

source: dataclinic.co.uk

The post How to FIX & Recover data from iPhone Error 14! appeared first on xFix.

Phoneboard is a free alternative to apps like ZXW, Wuxinji etc.
These paid apps cost up to a hundred bucks a year but Phoneboard is completely free.

Download for Windows

 Download for Linux

Download For Macs

Last version v1.9.0

v1.4.0
 * Added Dark Mode.
 * Ipad mini board.
 * When you are viewing only one side of the board, the search
   auto completion will show components of the active side only.
 * Added Diode values in iphone 6 board. 
 * Add Polish language [Translation by: Jakub Werwiński]
 * Add Hungarian language [Translation by: Dani Bá]
 * Add Cambodian language [Translation by: IC Fix Sothy]
 * Add Italian language [Translation by: Nicola Ripoccini]
 * Add Finnish language [Translation by: Ruuben Vuolasranta]
 * Add French languange [Translation by: Occaz'out]

v1.3.1:

  * Add Arabic language [Translation by: Haythem Hamdi]
  * Add Dansk language [Translation by: Olgierd Nowakowski]

The post Download Phoneboard – Free alternative to app like ZXW (Latest Version) appeared first on xFix.

Download iPhone XS Schematic: Download Here

Download iPhone XS MAX Schematic: Download Here

The post Download iPhone XS Max and iPhone XS Schematic Diagram appeared first on xFix.

Setup

That’s the first catch, of course: only 10 countries support Apple’s eSIMs, namely Austria, Canada, Croatia, the Czech Republic, Germany, Hungary, India, Spain, the U.K., and the U.S. Even then carriers must offer compatibility too, and initially the only supporting U.S. carriers for the XS and XS Max will be AT&T, T-Mobile, and Verizon. Sprint is planning to back the technology, but doesn’t yet have a date.

iPhone owners will also need an update to iOS 12 coming “later this year,” and a carrier’s official app or special QR code.

Many people will already have a nano-SIM card from their main carrier, in which case adding a second number involves adding a plan to the eSIM. If using a carrier app, the process is as simple as using that app to buy a plan — in the case of a QR code, you have to open the Settings app, tap Cellular, then “Add Cellular Plan.” You’ll be presented with an option to scan your code.

Notably you’ll be able to use the eSIM in place of a nano-SIM, whether for a single account or several, but you won’t be able to have more than one eSIM account active at a time. For most people then, the best option will be to have a nano-SIM primary.

Once multiple plans are running, you’ll be prompted to label them. There are preset options like “Primary,” “Secondary,” “Business,” and “Travel,” or you can simply create your own. To change a label later, you’ll have to go into the Settings app‘s Cellular menu, tap the number you want to change, then Cellular Plan Label.

You’ll also be asked to set a default number, which is critical since it will be the only one supporting the full range of cellular services. Secondary numbers can normally only field voice and SMS.

The exception is an option to relegate a secondary line to data only, which may be useful for traveling — this will let people call or message you at your main number but avoid exorbitant roaming fees with a local SIM card. Be warned that in addition to voice and SMS, iMessage and FaceTime will still go to your primary, which could rack up data fees.

Making calls

Once you’ve got things up and running, you can switch numbers before dialing in the Phone app by tapping the current one directly from the keypad, or else hitting the “i” button first when you’re browsing Favorites. Picking an SMS number is similar, but you tap the number after starting a new conversation and selecting a contact.

Changing the line for iMessage and FaceTime is more complicated, as you have to go into Settings, Messages, and then iMessage & FaceTime Line. The selected choice is permanent until you reverse it.

There’s one last thing to note, which is iOS 12’s status bar info. You’ll normally only see signal strength for one line at a time, but you can see how a secondary is doing by opening up Control Center.

The post How dual-SIM (eSIM) works with Apple’s iPhone XS & XS Max appeared first on xFix.

Even though some codes may not be compatible with all kinds of smartphones, most of them should work, in general. xFix Repairs brings to you a list of  50+ Android’s Secret Codes that will make your life easier and practical.

Cool Android Secret Codes 2018

1. Discover IMEI

* # 06 # – Code to discover the IMEI of your smartphone. An important information in case you need to lock the device some day.

2. Turn off your smartphone

* # * # 7594 # * # * – To turn off the phone directly by pressing the power button and without having to see any menu.

3. Display device information

* # * # 4636 # * # * – Displays general information about your device, battery usage and Wi-Fi.

4. Do Factory Restore

* # * # 7780 # * # * – Performs an automatic factory restore on your smartphone, erasing all apps, files, and general information.

Note: Do not enter unless you want to perform this restore!

5. Delete everything from the phone

* 2767 * 3855 # – Erases everything from your device, including the firmware, so do not type it unless you know what you’re doing!

6. Backup photos and videos

* # * # 273283 * 255 * 663282 * # * # * – Quickly backs up your photos and videos on your smartphone.

7. Test the GPS

* # * # 1472365 # * # * – Smartphone performs a GPS check on your smartphone.

8. Display Firmware Information

* # * # 1234 # * # * – Access the general firmware information of your device.

9. Show Wi-Fi Mac Address

* # * # 232338 # * # * – Checks the Mac address of a Wi-Fi on your smartphone.

10. Access the Gtalk service

* # * # 8255 # * # * – This code is for you to monitor Gtalk services.

11. Access Email Information

* # * # 36245 # * # * – This code will display debug information for your registered Primary email on the device. Not particularly useful for casual Android users.

12. View calendar events

* # * # 225 # * # * – This code will take you directly to the calendar events of your device.

13. Camera Information

* # * # 34971539 # * # * – To view some general information about the camera of your device, just enter this code.

14. Internal lighting test

* # * # 0842 # * # * – Enter this code to start a test of the internal illumination of the device. Do not do it if you do not have more advanced knowledge of Android.

15. Touch Screen Test

* # * # 2664 # * # * – With this code, you will start a touch screen test of your smartphone. Also, do not enter it if you do not have advanced knowledge of Android.

16. Software and Hardware Information

* # 12580 * 369 # – This code will show some general information about the software and hardware of your device.

17. Device lock status

* # 7465625 # – With this code you will see the current status of your smartphone lock.

18. Wireless LAN Testing

* # * # 232339 # * # * – This is another code that will start a test, this time in relation to Wireless LAN. Only do it if you know what you are doing and if you have any use for this test specifically.

19. Screen Testing

* # * # 0 * # * # * – This code can perform a small test of the LCD screen of some smartphones, but does not work with all current models.

20. Audio Testing

* # * # 0673 # * # * OR * # * # 0289 # * # * – These two codes can trigger a quick audio test of your device.

21. Touch Screen Information

* # * # 2663 # * # * – When you enter this code, the device will display some general information about the touch screen of your smartphone.

22. Version of RAM memory

* # * # 3264 # * # * – When you enter this code on your smartphone, you can see more information about the device’s RAM.

23. Proximity sensor test

* # * # 0588 # * # * – This code will test the device’s proximity sensor, but it will only work on some models.

24. Bluetooth test

* # * # 232331 # * # * – Perform some tests with your Bluetooth when typing this code on your smartphone.

25. Device Bluetooth information

* # * # 232337 # * # – Check out more detailed information about the Bluetooth of your device as you enter this code.

26. Check the USB

* # 08008 # – This code is for you to check the current status of the USB of your device. It tends to work better on older devices.

27. Service menu

* # 0 * # – Enter this code to enter the service menu of your smartphone, where you can perform various actions and check information.

28. Enter test mode

*# * # 197328640 # * # * – With this code, you will enter an Android testing mode. Do not do this unless you have a good working knowledge of the operating system and know what you are doing.

29. Software version

* # * # 1111 # * # * – This code will display information about the current software version of your device.

30. Hardware version

* # * # 2222 # * # * – This code will display information about the current hardware version of your device.

31. Activate voice dialing

* # * # 8351 # * # * – With this code, you will activate voice dialing. This may not work on all current devices.

32. Disable voice dialing

* # * # 8350 # * # * – Using the code will deactivate voice dialing, if you have enabled it before.

33. Field Test

* # * # 7262626 # * # * – Use this code to conduct a field test with your Android, but do not type it if you do not have a good understanding of the system.

34. Diagnostic Configuration

* # 9090 # – This code will show the diagnostic configuration of your smartphone. It may not work on some devices and is not recommended for casual Android users.

35. Remove Google account

* # * # 7780 # * # * – Use this code to remove all settings from your Google account on your phone. Do not do this if you do not have the most advanced knowledge of Android.

36. Reinstall firmware

* 2767 * 3855 # – This code can help you to reinstall the firmware of your device. Do not perform the procedure if you do not understand the subject, as it may end up causing problems to your smartphone.

37. Product code

* 2767 * 4387264636 * – You can enter this code to display the product code of your smartphone.

38. Update menu

* # 8736364 # – This code takes you straight to the Android update menu, which can also be found normally in the device settings.

39. Data usage status

* # 3282 * 727336 * # – With this code, you can have more information about the data usage status of your smartphone.

40. Data Creation

* # 273283 * 255 * 3282 * # – This code will take you to a data creation menu on your smartphone. It is not very recommended for casual users and may not work with all types of current smartphones.

41. Secret menu

* # * # 4986 * 2650468 # * # * – With this code you can enter a secret menu of your smartphone. It will basically show information you would not normally find on the device.

42. Build the device

* # * # 44336 # * # * – Use this code to learn more about Device Build, such as the version code of Android installed on it.

43. Wi-Fi Test

* # * # 528 # * # * – Use this code to do a quick Wi-Fi test of your device.

44. SDPA / HSUPA Panel

* # 301279 # – Use this code to access the SDPA / HSUPA control panel of your device.

45. Test Menu

# * # 3424 # * # * – Using this code, you will open a test menu for various functions of the device.

46. Hard Reset

* # * # 786 # * # * – Use this code to perform Hard Reset on your device.

47. Settings Superuser

* # * # 7873778 # * # * – To open your Superuser settings, simply enter this code. Do not attempt to make any changes if you do not have a possess knowledge on the subject.

48. Check for Updates

* # * # 2432546 # * # * – Enter this code to see if updates are available for your device.

49. Camera Firmware

* # 34971539 # – Use this code to check camera firmware information.

50. FactoryKeystring

* # 7284 # – This code gives you access to the device’s FactoryKeystring. Do not enter it without prior knowledge.

51. Battery information

* # 0228 # – Use this simple code to check more information about your battery. It may not work with all smartphones.

52. USB Control

* # 872564 # – Use this code to gain access to the USB log control of your smartphone.

Conclusion Android secret dialer codes,

So, what did you think of our 50+ collection of Android’s secret dialer codes? Try them on your smartphone (use appropriate caution as advised above), and let us know of your experiences in the comments section. Also, do share the post if you like it on Facebook, Twitter and everywhere else.

The post 50+ Android Dialer Codes To Bring The Hidden Options appeared first on xFix.

Apple’s official MFi Certified logo is regularly seen on many third-party accessory packages. The MFi certified logo covers the full range of iDevices accessories. It is an abbreviation for “Made for iPod, iPhone, and iPad”. MFi unblocks business opportunity for third-party accessory manufactures and forces them to ensure their products meet Apple’s standards. And the MFi certified accessories are recommended to be used with your iDevice. Today we are going to discuss about MFi certified lightning cables.

MFi Lightning Cables

The original 30-pin dock connector was superseded by the lightning connector in 2012. And the lightning connector is currently Apple’s proprietary connector for charging and data transmitting. A tiny authentication chip inside each lightning connector makes Apple MFI Certified easy to tell. Non-certified or knock-off lightning cables will harm your devices as a long run. These cables can often get extremely hot and at the same time as that might be the source of iDevices overheating.

Non-MFi Lightning Cables

Non-MFi Certified cables can be purchased from various resellers with a much less than a certified cable price. Predictably, cheaper is not always better. Many unqualified manufactures lead the market to confusion. According to Apple, non-MFi Certified cables are not subjected to industry-standard consumer safety testing and are poorly constructed with inferior or missing components, flawed design, and inadequate electrical insulation. These non-MFi certified cables have the potential to overheat, catch fire, and deliver a deadly electric shock to consumers while in normal use.

So many customers who have used non-MFi Cables had their logic board (the Motherboard) shorted by bad voltage delivery. Once a logic board has been shorted, the cost to repair becomes almost the same as a new device.

Verification

The iDevices will notify you if you are using a non-MFi cable with the message “This cable or accessory is not certified and may not work with you device.” When purchasing chargers or charge cables, make sure you are getting an Apple approved product with MFi logo.

The post Important Info about MFI Certified USB Cables appeared first on xFix.

Recently, unauthorized third-party repair outlets are affected by a problem – the screen repair on iPhone 8/8 Plus/X disables the device’s ability to adjust brightness automatically. It’s not a problem only appear on the iPhone with aftermarket iPhone LCD screens but also with original and OEM screens.

Yet, the aftermarket repair community hasn’t come up with any solution to this issue. But solved by ”The Light Sensor Programmer Box”, it can be easily fixed by using ”The Light Sensor Programmer Box”. It’s a magic box which can transmit the data from the original cracked screen to the new display replacement. Once the transmission completed, the Ambient Light Sensor comes back to life.

The Light Sensor Programmer Box for iPhone 8 8 Plus X LCD Screen Code Files Programming Device Phone Repair Tools
​

Features:
* This programmer is used to solve light sensor not working issue after screen replacement.
* To solve the auto-brightness issue by reading the firmware data of the original screen, and write the information into the replacement screen.
* Please note: This Programmer can only be used for original screens, aftermarket screens are under developing.

1. It fit for iPhone X, 8, 8P
2.Support Chinese and English
2. Support offline and online operation, with touch screen, easy and quick operation!
3. You can back up more than 200 pieces of code files, then you can save into the computer. When you use the replacement screen to replace the customer’s original screen, you can backup the code files of the original screen!
4. If the customer’s replacement screen damaged again, you can easily write the information into the new replacement screen.

Introduction
”The Light Sensor Programmer Box” is for iPhone 8, 8 Plus, X which assures its functionality to automatically adjust brightness by data transforming.

The post How To Fix Auto-brightness Issue on iPhone 8, 8P, X – Video Instruction appeared first on xFix.

Baseband  is commonly known as BB, Baseband can be defined as a communication module. It contains a communication system. It is usually used to control iPhone’s communication procedures, telephone communications, WiFi wireless communications, as well as Bluetooth communications.

The Baseband manages all the functions which require an antenna. The baseband processor has its own RAM and firmware in NOR flash, separate from the ARM core resources. The baseband is a resource to the OS. The Wi-Fi and Bluetooth are managed by the main CPU, although the baseband stores their MAC addresses in its NVRAM.

All iPhones have a baseband, and iPhone baseband is essentially the cellular modem firmware that is on your iPhone. Specifically, baseband includes the low level software that is running on the iPhones cellular modem hardware, the combination of which allows the iPhone to connect to a cellular network to send and receive data, phone calls, and transmissions.

Warm Prompt:

iPhone’s signal is directly related to its baseband IC. Under normal circumstances, if you upgrade the firmware of your iDevice, it’s baseband will follow the upgrade.

Additionally, baseband is also what keeps the device locked to the intended carrier, in the USA, this is commonly AT&T, Verizon, T-Mobile, Sprint, and some smaller other carriers. Buying an unlocked iPhone would not have that baseband lock, for example.

How to check iPhone’s baseband?

A1. Launch Settings app of your iPhone -> click General.

A2. Continue to click About -> Modern Firmware.

The iPhone’s baseband processor is the S-Gold 2.

The iPhone 3G, the iPhone 3GS and the iPad make use of the X-Gold 608 chip for this purpose.

The iPhone 4 (iPhone3,1) and iPad 2 (iPad2,2) use the XMM 6180.

The iPhone 4 (iPhone3,3) uses the MDM6600 and the iPhone 4S uses the MDM6610.

iPad 3 uses MDM9600.

iPad 4, iPad Air , iPad mini, iPad mini 2, iPad mini 3, iPhone 5, iPhone 5c and iPhone 5s use MDM9615.

iPad Air 2, iPad Pro (12.9 inch), iPad mini 4, iPhone 6, iPhone 6 Plus and iPhone SE use MDM9625.

iPhone 6s, iPhone 6s Plus and iPad Pro (9.7 inch) use MDM9635.

The post What is iPhone Baseband IC or Modem Firmware? appeared first on xFix.

In January, Apple took down a web tool that allowed anyone to check status of the theft-deterrent Activation Lock feature. While the link to the iCloud Activation Lock webpage is now dead and the associated support document detailing Activation Lock no longer references the tool, We have discovered that potential buyers in the market for a secondhand iOS device can still check Activation Lock status by IMEI through Apple’s Support website.

IMPORTANT: The workaround doesn’t always work properly so your mileage may vary.

As explained before, Apple most likely took down the iCloud Activation Lock web tool for security purposes, to stop hacks relying on stolen serial numbers.

iCloud Activation Lock allowed anyone to check if a used iPhone, iPad, iPod touch or Apple Watch was lifted. Some folks have been known to leverage the tool when reactivating a bricked device: hackers would typically enter a device’s IMEI on the now erstwhile iCloud Activation Lock webpage to decipher its serial number, then change the hardcoded serial number stored on the device to bypass Activation Lock.

How to check Activation Lock status via Apple Support pages

1) Visit Apple’s Support website in your browser.

2) Select iPhone from the list of devices.

3) Click any search category related to hardware, like Battery or Repairs & Physical Damage, then select a specific problem like “Buttons not working”.

4) On the next page, click Send in for Repair.

5) On the next screen, enter your device’s serial number, IMEI or MEID to check its Activation Lock status.

If Find My iPhone and Activation Lock are enabled on the device, you should see a message saying “Sorry but we can’t create a repair while Find my iPhone is active”.

Tip: If you don’t see this option listed, go back and select a different device problem.

We fully expect to see Apple remove this obvious loophole soon.

Source: UnlockBoot

The post How to Check iPhone iCloud Activation Lock Status [New Method] appeared first on xFix.